ConcreteGauge / Curb and gutter
Curb and gutter concrete calculator
Enter the length of the run and the four measurements of the cross-section. The drawing shows the section you have described.
What to buy
22 cubic feet
0.81 cubic yards, or 0.623 cubic metres. Includes 10% extra for spills and uneven ground. Without it: 20 cubic feet.
Mix it from bags
37 bags of 80 lb
About $240.50. That is 2,960 lb to carry and mix.
Best for this job: under one cubic yard, bags are simpler than a delivery.
Order ready-mix
1 cubic yard
About $150.00 before delivery fees. Rounded up to the next quarter yard, the way suppliers sell it.
| 40 lb bags | 74 |
|---|---|
| 50 lb bags | 59 |
| 60 lb bags | 49 |
| 80 lb bags | 37 |
The concrete weighs about 3,300 lb once poured.
The four measurements of the section
Look at the curb from its end, as in the drawing. It is an L on its side.
- Curb depth: how thick the upright part is, front to back.
- Curb height: how far the upright part stands above the gutter.
- Gutter width: the flat part in front of the curb, where water runs.
- Flag thickness: how thick the flat base is. It runs under the curb as well as the gutter.
The length is measured along the curb. For a curve, measure along the curve itself with a tape or a wheel, not straight across.
The formula
(Gutter width × flag thickness + curb depth × (curb height + flag thickness)) × length.
For 20 feet with a 6 inch curb, 6 inches high, a 12 inch gutter and a 6 inch flag:
- Gutter: 1 × 0.5 = 0.5 square feet
- Curb: 0.5 × (0.5 + 0.5) = 0.5 square feet
- Section: 1 square foot; × 20 feet = 20 cubic feet, or 0.74 cubic yards
- Add 10%: 0.81 cubic yards
Concrete per run
For a curb 6 inches deep and 6 inches high on a 6 inch flag, with 10% extra already added.
| Section | Cubic feet per 10 ft | Cubic yards per 50 ft | Cubic yards per 100 ft |
|---|---|---|---|
| 12 in gutter | 11.00 | 2.04 | 4.07 |
| 18 in gutter | 13.75 | 2.55 | 5.09 |
| 24 in gutter | 16.50 | 3.06 | 6.11 |
Curb with no gutter
For a plain upright curb, set the gutter width to 0. The curb height is then the part above the base and the flag thickness is the part below it: a curb 6 inches thick and 12 inches tall in total, 20 feet long, takes 11 cubic feet to buy.
Shaped and sloped sections
Real curbs are rarely perfect rectangles: the face leans back, the top edge is rounded and the gutter falls toward the curb. These take a little concrete away and the calculator’s square section slightly overstates the amount, by a few percent on a typical section. That margin is on the safe side, so the usual 10% extra covers it comfortably.
Curbs along a public street are built to the city’s or county’s standard drawing, which gives every one of these measurements. Ask the engineering or public works department for it before you form anything at the road.
A dropped section where a driveway crosses is thinner in the curb and thicker in the flag; work it out as its own run. The driveway apron behind it is a slab.
Questions people ask
How much concrete is in 100 feet of curb and gutter?
With a 6 inch curb standing 6 inches above a 12 inch gutter on a 6 inch flag, 100 feet takes 4.07 cubic yards including 10% extra. With an 18 inch gutter it takes 5.09, and with a 24 inch gutter 6.11.
How do I calculate concrete for a curb?
Find the area of the section seen from the end, in square feet, and multiply it by the length in feet. For a curb and gutter the section is two rectangles: the flat gutter, and the upright curb down to the bottom of the base.
What is the flag?
The flat slab that forms the gutter and runs on under the curb. Its thickness is the depth of concrete under the gutter line.
How many feet of curb will one cubic yard pour?
The section in the example is 1 square foot, so one cubic yard, which is 27 cubic feet, pours 27 feet with nothing spare, or about 24 feet once 10% is kept back for waste.
Can I use this for landscape edging?
Yes. Set the gutter width to 0 and enter the edging as a curb: its thickness as the curb depth and its full height split between the curb height and the flag thickness.
Where the numbers come from
- The section is worked out as two rectangles, which is standard geometry. No code figures are used on this page: street curbs follow your local standard drawing.
- Bag yields: a 40 lb bag makes about 0.3 cubic feet, 50 lb about 0.375, 60 lb about 0.45 and 80 lb about 0.6 (ArcSite, Concrete Network). Brands differ a little, so check the yield printed on your bag.
- Bag yields outside the United States: in the United Kingdom and Ireland a 20 kg bag makes about 0.01 cubic metres (Blue Circle, at Travis Perkins); in Australia and New Zealand 108 bags of 20 kg make a cubic metre (Boral); in Canada a 30 kg bag makes about 0.44 cubic feet (Quikrete, at Home Depot Canada). The 25 kg figures are worked out in proportion.
- Weight: 150 lb per cubic foot for normal concrete (Omni Calculator).
Every formula on this page is checked by an automatic test each time the site is updated. Last reviewed 15 November 2026.