ConcreteGauge

ConcreteGauge / Wire mesh

Wire mesh calculator for concrete

Enter the size of the slab and choose how your mesh is sold. You get the sheets or rolls to buy, with the overlaps allowed for.

One full square of the mesh is usual: 6 inches for 6 × 6 mesh.

More options: extra for waste

Mesh to buy

11 sheets, 5 × 10 ft

To cover 400 square feet. Includes 10% extra for cuts and offcuts.

Each sheet is 50 square feet, but covers 42.8 once it overlaps its neighbours by 6 inches on two sides.

That is 550 square feet of mesh bought. Set it on chairs or lift it into the concrete as you pour: mesh lying on the ground does nothing.

20 ft20 ftDashed lines: where sheets meet

Why the overlap matters

Sheets of mesh are not butted edge to edge. Each one overlaps the next so the steel is continuous, and that overlap is mesh you buy but do not get to count as coverage. With a 6 inch overlap, a 5 × 10 foot sheet of 50 square feet covers 42.75.

Sheets = area ÷ ((sheet width − overlap) × (sheet length − overlap)), rounded up.

For a 20 × 20 foot slab: 400 square feet plus 10% is 440, and 440 ÷ 42.75 = 10.29, so 11 sheets.

Mesh for common slabs

With a 6 inch overlap and 10% extra.

SlabArea5 × 10 ft sheets8 × 20 ft sheets5 × 150 ft rolls
10 × 10 ft100 sq ft311
12 × 12 ft144 sq ft421
12 × 16 ft192 sq ft521
16 × 20 ft320 sq ft931
20 × 20 ft400 sq ft1141
24 × 24 ft576 sq ft1551
24 × 30 ft720 sq ft1962
30 × 40 ft1,200 sq ft31102

Sheets or rolls?

Mesh for home slabs is sold as flat sheets, most often 5 × 10 feet, and as rolls 5 feet wide and 150 feet long. Larger 8 × 20 foot sheets come from concrete suppliers. A roll is cheaper for the area but wants to curl back up, and has to be flattened before it will stay where you put it. Sheets lie flat and are easier for one person.

The usual overlap is one full square of the mesh: 6 inches for the common 6 × 6 pattern. Tie the overlaps so the sheets move as one.

Reading the label

A label such as 6 × 6 W1.4/W1.4 means wires 6 inches apart in both directions, and the W number is the size of the wire. Older labels give the same thing as a gauge, 6 × 6 10/10. Heavier wire has a larger W number and a smaller gauge.

Mesh holds cracks tight; it does not stop them and it does not make a thin slab carry a heavy load. For bars instead of mesh, see the rebar calculator. Where the cracks should go is the job of the control joint calculator.

Questions people ask

How many sheets of wire mesh do I need for a 20 × 20 slab?

11 sheets of 5 × 10 feet, or 4 sheets of 8 × 20 feet, with a 6 inch overlap and 10% extra.

How much area does a 5 × 10 sheet of mesh cover?

It is 50 square feet, but once it overlaps its neighbours by 6 inches on two sides it covers about 42.8 square feet.

How much does a roll of wire mesh cover?

A 5 × 150 foot roll is 750 square feet. With a 6 inch overlap along its length it covers about 673 square feet.

How much should wire mesh overlap?

At least one full square of the mesh, which is 6 inches for 6 × 6 mesh, tied together. Follow your plans if they ask for more.

Where does the mesh sit in the slab?

Inside the concrete, not on the ground. Support it on chairs before the pour, or lift it into place as the concrete goes down.

Where the numbers come from

Every formula on this page is checked by an automatic test each time the site is updated. Last reviewed 15 November 2026.

What you may need next