ConcreteGauge / Rebar
Rebar calculator for concrete slabs
Enter the size of the slab, the spacing of the grid and the bar size. You get the bars in each direction, the lengths to buy and what they weigh.
Steel to buy
46 bars of #4, 20 ft long
901 feet of bar in all, weighing about 602 lb. Includes 10% extra for cuts and offcuts.
| Direction | Bars | Each |
|---|---|---|
| Along the length | 21 | 19.5 ft |
| Across the width | 21 | 19.5 ft |
The bars cross at 441 points. Tie enough of them to hold the grid still, and set it on chairs so it sits inside the concrete, not on the ground.
How the grid is counted
The bars stop short of the forms on every side, so the grid is a little smaller than the slab. Within it the bars are spread evenly and never further apart than the spacing you set, which means the count rounds up.
For a 20 × 20 foot slab with bars 12 inches apart and 3 inches clear at each edge:
- Each bar is 20 feet less 3 inches at both ends: 19.5 feet
- 19.5 feet ÷ 1 foot = 19.5 spaces, rounded up to 20, so 21 bars each way
- 21 × 19.5 × 2 directions = 819 feet of bar
- Add 10%: 901 feet, which is 46 bars of 20 feet, about 602 lb in #4
Bars for common slabs
20 foot bars of #4 and their weight, with 3 inches clear at the edges and 10% extra.
| Slab | 12 in apart | 18 in apart | 24 in apart |
|---|---|---|---|
| 10 × 10 ft | 12 bars · 154 lb | 9 bars · 112 lb | 7 bars · 84 lb |
| 12 × 12 ft | 17 bars · 220 lb | 12 bars · 152 lb | 9 bars · 118 lb |
| 12 × 16 ft | 22 bars · 292 lb | 16 bars · 204 lb | 12 bars · 156 lb |
| 16 × 20 ft | 37 bars · 483 lb | 25 bars · 331 lb | 20 bars · 254 lb |
| 20 × 20 ft | 46 bars · 602 lb | 31 bars · 401 lb | 24 bars · 315 lb |
| 24 × 24 ft | 70 bars · 925 lb | 48 bars · 629 lb | 36 bars · 481 lb |
| 24 × 30 ft | 86 bars · 1,146 lb | 59 bars · 778 lb | 45 bars · 594 lb |
| 30 × 40 ft | 144 bars · 1,915 lb | 98 bars · 1,302 lb | 74 bars · 985 lb |
Bar sizes
The number on a bar is its diameter in eighths of an inch: #4 is four eighths, or half an inch.
| Bar | Diameter | Weight per foot | 20 ft bar | 40 diameters |
|---|---|---|---|---|
| #3 | 0.375 in | 0.376 lb | 7.52 lb | 15 in |
| #4 | 0.5 in | 0.668 lb | 13.36 lb | 20 in |
| #5 | 0.625 in | 1.043 lb | 20.86 lb | 25 in |
| #6 | 0.75 in | 1.502 lb | 30.04 lb | 30 in |
Slabs longer than one bar
When the slab is longer than the bars you can buy, each line of steel is made from two or more pieces that overlap. A common rule sets the overlap at 40 times the bar’s diameter, the last column above; your plans may ask for more. The calculator adds the overlaps for you: a 30 × 40 foot slab at 12 inches needs 2,606 feet of bar before waste, not the 2,434 feet the bare grid would suggest.
What size and spacing?
That is a design decision, not a counting one, and this page does not make it. Use the size and spacing on your plans or from your building department. If the slab is a simple patio or path with no plans, ask your concrete supplier what is normal locally, or whether mesh would do: see the wire mesh calculator.
For the concrete that goes round the steel, start from the slab calculator.
Questions people ask
How much rebar do I need for a 20 × 20 slab?
With #4 bar 12 inches apart, 46 bars of 20 feet, about 602 lb, including 10% extra. At 18 inches apart it is 31 bars.
How many pieces of rebar are in a grid?
Divide the length of the grid by the spacing, round up, and add one for the bar at the end. Do that for each direction. A 20 foot slab at 12 inches has 21 bars each way.
How much does #4 rebar weigh?
0.668 lb per foot, so a 20 foot bar weighs 13.36 lb.
How much should rebar overlap?
A common rule is 40 times the bar diameter: 20 inches for #4 and 25 inches for #5. Structural drawings often specify their own figure, which takes priority.
Does the calculator include waste?
Yes, 10% unless you change it under “More options”. Offcuts from one line can often start the next, so careful cutting wastes little.
Where the numbers come from
- Outside the United States: 10, 12 and 16 mm bars weigh 0.617, 0.888 and 1.58 kg a metre (Reinforcement Products Online for Britain; the same in Australia, InfraBuild). Canadian 10M, 15M and 20M bars weigh 0.785, 1.57 and 2.355 kg a metre (Russel Metals). The bar length opens at 6 m, the length merchants stock (Jewson, Wagner).
- Bar weights per foot: Firgelli, Rebar Weight Calculator, giving the ASTM A615 nominal weights.
- The 40 diameter overlap rule: Easy Unit Converter, Rebar Calculator.
- Bag yields: a 40 lb bag makes about 0.3 cubic feet, 50 lb about 0.375, 60 lb about 0.45 and 80 lb about 0.6 (ArcSite, Concrete Network). Brands differ a little, so check the yield printed on your bag.
- Bag yields outside the United States: in the United Kingdom and Ireland a 20 kg bag makes about 0.01 cubic metres (Blue Circle, at Travis Perkins); in Australia and New Zealand 108 bags of 20 kg make a cubic metre (Boral); in Canada a 30 kg bag makes about 0.44 cubic feet (Quikrete, at Home Depot Canada). The 25 kg figures are worked out in proportion.
- Weight: 150 lb per cubic foot for normal concrete (Omni Calculator).
Every formula on this page is checked by an automatic test each time the site is updated. Last reviewed 15 November 2026.