ConcreteGauge / Control joints
Concrete control joint calculator
Enter the size and thickness of the slab. You get how many joints to cut each way, the size of the panels and how deep to cut.
Where to cut
3 joints to cut
56 feet of joint in all, each at least 1 inch deep. Joints may be up to 10 feet apart for this thickness.
| Joints | Count | Spaced |
|---|---|---|
| Across the slab | 2 | every 8 ft |
| Along the slab | 1 | every 8 ft |
6 panels of 8 × 8 feet.
The rule
Concrete shrinks as it dries and will crack. Control joints are lines of weakness that make it crack where you choose, in a straight line at the bottom of a groove.
Furthest apart, in feet = 2 to 3 × the slab’s thickness in inches. Depth of cut = a quarter of the thickness.
That is the rule Concrete Network gives for plain slabs: 8 to 12 feet apart for a 4 inch slab. Engineers writing for the trade recommend staying at 2 to 2.5 times for better control, which is why the calculator opens at 2.5.
| Slab thickness | 2 × | 2.5 × | 3 × | Cut at least |
|---|---|---|---|---|
| 3.5 in | 7 ft | 8.8 ft | 10.5 ft | 1 in |
| 4 in | 8 ft | 10 ft | 12 ft | 1 in |
| 5 in | 10 ft | 12.5 ft | 15 ft | 1.25 in |
| 6 in | 12 ft | 15 ft | 18 ft | 1.5 in |
| 8 in | 16 ft | 20 ft | 24 ft | 2 in |
How the layout is worked out
The slab is divided into equal panels, none longer than the limit. For a 24 × 16 foot slab 4 inches thick at 2.5 times:
- Limit: 2.5 × 4 = 10 feet
- 24 feet ÷ 10 = 2.4, so 3 panels of 8 feet, with 2 joints across
- 16 feet ÷ 10 = 1.6, so 2 panels of 8 feet, with 1 joint along
- 2 × 16 + 1 × 24 = 56 feet of joint, cut 1 inch deep
Joints for common slabs
For slabs 4 inches thick at 2.5 times, a limit of 10 feet.
| Slab | Joints | Panels | Feet of joint |
|---|---|---|---|
| 10 × 10 ft | 0 | 10 × 10 ft | 0 ft |
| 12 × 12 ft | 2 | 6 × 6 ft | 24 ft |
| 12 × 16 ft | 2 | 6 × 8 ft | 28 ft |
| 16 × 20 ft | 2 | 8 × 10 ft | 36 ft |
| 20 × 20 ft | 2 | 10 × 10 ft | 40 ft |
| 24 × 24 ft | 4 | 8 × 8 ft | 96 ft |
| 24 × 30 ft | 4 | 8 × 10 ft | 108 ft |
| 30 × 40 ft | 5 | 10 × 10 ft | 170 ft |
Keep the panels square
A long thin panel cracks across its middle whatever the spacing says. The guidance is to keep the long side no more than one and a half times the short side, and squarer is better. The calculator warns you when a layout breaks that, and the cure is one more joint.
- Run joints right across the slab. A joint that stops part way invites a crack to finish it.
- Put a joint at every inside corner, such as where a path meets a patio: cracks start there.
- Cut early. Sawn joints go in as soon as the concrete can take the saw without tearing; grooved joints are tooled while it is still workable.
Joints do not stop cracks, they hide them. Steel holds the cracks closed: see the wire mesh and rebar calculators. Once the slab has cured, the sealer calculator covers the finish.
Questions people ask
How far apart should control joints be in a 4 inch slab?
No more than 8 to 12 feet, which is 2 to 3 times the thickness in inches, taken as feet. Staying at 8 to 10 feet gives better control of cracking.
How deep should control joints be?
At least a quarter of the slab’s thickness, and not less than 1 inch: 1 inch in a 4 inch slab and 1.5 inches in a 6 inch slab.
How many control joints does a 20 × 20 slab need?
At 4 inches thick and 2.5 times, 2 joints, making panels of 10 × 10 ft: 40 ft of joint in all.
Do I need control joints in a small slab?
A slab no longer than the limit in either direction needs none. At 4 inches thick and 2.5 times that means up to 10 × 10 feet.
What is the difference between a control joint and an expansion joint?
A control joint is a groove part way through the slab that tells a shrinkage crack where to form. An expansion, or isolation, joint is a gap the full depth of the slab, filled with a soft strip, that separates the slab from a wall, a post or another slab.
Where the numbers come from
- In metric countries the same rule is written as 24 to 36 times the slab thickness, which is 2 to 3 feet for each inch.
- Spacing of 2 to 3 times the thickness and depth of a quarter: Concrete Network, Contraction Joints.
- The 2 to 2.5 times recommendation, the 1 inch minimum depth and panel proportions: For Construction Pros, Rules for Designing Contraction Joints.
- Bag yields: a 40 lb bag makes about 0.3 cubic feet, 50 lb about 0.375, 60 lb about 0.45 and 80 lb about 0.6 (ArcSite, Concrete Network). Brands differ a little, so check the yield printed on your bag.
- Bag yields outside the United States: in the United Kingdom and Ireland a 20 kg bag makes about 0.01 cubic metres (Blue Circle, at Travis Perkins); in Australia and New Zealand 108 bags of 20 kg make a cubic metre (Boral); in Canada a 30 kg bag makes about 0.44 cubic feet (Quikrete, at Home Depot Canada). The 25 kg figures are worked out in proportion.
- Weight: 150 lb per cubic foot for normal concrete (Omni Calculator).
Every formula on this page is checked by an automatic test each time the site is updated. Last reviewed 15 November 2026.